Shower Handle Replacement For Common Shower Problems

Are you sick and tired of your jammed or leaky shower handle? It's in your hands to replace the broken handle. It not only makes your shower more pleasant to use, but it also adds to the beauty of your bathroom.

The shower handle is the operational center of your daily shower. It's the sole part that lets you fine-tune the temperature and water pressure. So, it completely disrupts your day if it fails to function as expected. Don't allow a broken shower handle to dampen your enthusiasm for the day.

This article will discuss the value of professional shower handle replacement services and provide clear instructions for doing so yourself. It also outlines the tools, materials, and steps involved in replacing such handles.

Common Shower Problems

Problems with the shower handle can cause a major inconvenience to our daily routine. A few of them are as follows:

Leaking Shower Handle

Are you sick of hearing the dripping sound of your shower handle all the time? Well, there can be a number of potential causes including:

• 
  The washer inside the handle of the shower can wear down over time, allowing water to flow through. 
• When the O-ring is damaged water might seep in through the grip. 
• Water leakage can also be caused by corrosion of the valve seat or damage to the handle.

Stuck Shower Handle

If the shower's handle is jammed or stuck, you may not be able to turn it off or change the water's temperature. Mineral deposits or a broken handle are just some of the potential causes of this type of plumbing issue. Additionally, corrosion is another reason that can cause the valve stem to become fused to the handle. The uncomfortable and frustrating problem of a jammed shower handle can be fixed by performing routine maintenance and repairs.

Loose Shower Handle

A slow but constant leak that might accumulate over time when the handle is loose. Water waste from a loose shower handle can result in higher water costs. If you want to avoid this kind of issue, you must take corrective measures immediately. Additionally, remember that an Allen or hex wrench is typically used to loosen or tighten a set screw in this situation.

Tools & Materials Required

Your shower handle needs to be replaced if you are having trouble turning it or if it isn't functioning as it should. Fortunately, all it takes to replace a shower handle is a few simple tools and a few minutes. The necessary tools and materials required for replacing shower handles are as follows:

• A screwdriver is required to remove the old shower handle's screws. The screwdriver you'll need to use will depend on the type of shower handle you have.
• If the shower handle is fastened with an Allen screw, you will need an Allen wrench, so choose the right size carefully.
• You'll need a new one to replace the old one. If you need to replace the handle on your shower faucet, pick one that fits your valve and can be installed using the same hardware.
• Installing a new shower handle requires a tiny amount of silicone sealant to be applied to the base of the handle prior to installation. If water is able to get behind the handle, it won't do any harm.

Steps To Replace Shower Handle

Although it is a difficult chore at first, replacing a shower handle is quite simple if the proper equipment and procedures are used. These are the measures to take:

Step-1 Turn Off The Water Supply

You need to switch off the water supply to your shower before you start using it. To do this, you'll need to either turn off your home's main water supply or the valve that supplies water to your shower. It's common to find this valve in the basement or near the bathroom.

Step-2 Remove The Old Shower Handle

Next, you'll need to get rid of the old shower handle. To do this, locate the fasteners that are keeping the grip in place, such as a screw or bolt. Pull the handle away from the wall carefully after removing the screws or using a wrench.

Step-3 Install New Shower Handle

The old shower handle must be removed before the new one can be installed. Make sure you have everything you need to install your new handle by consulting the manual that came with it. Finally, insert the screws or bolts that come with the new handle into the wall holes.

Step-4 Secure The Handle With Screws

After the handle has been positioned, any loose screws or bolts should be tightened using a screwdriver or tool. Once the screw is firmly in place, test the handle to make sure it turns on and off without wobbling or falling free. If the handle is still loose after tightening the screw, you should probably get a new one. 

Step-5 Apply Silicone Sealant

A small amount of silicone sealant applied around the base of the handle will prevent water from seeping behind it and causing harm. Smooth a thin, even layer of silicone with a caulk gun using your finger or a caulk smoothing tool.

Step-6 Test The New Shower Handle

After installing the shower handle and reconnecting the water supply, you should run a test to make sure it is in good working order. Locate the source of the leak or drip, and fix it, if necessary, at the base of the handle.

Conclusion

Water damage, mold growth, and higher water bills are just some of the consequences of ignoring a broken shower handle. Changing the handle stops these problems from occurring and improves the quality of your shower by restoring your ability to regulate the water's temperature.

Since working with water pipes and valves can be dangerous, it's best to leave replacing shower handles to the professionals at Cannon Plumbing. Our plumbing experts have years of experience in providing shower handle replacement services. We have teams of licensed and insured plumbers to provide excellent services. Our plumbers always prioritize your plumbing satisfaction. For more information, Contact Us Today!